PRODUCTS Photostrip

PDF files can be viewed, downloaded, or printed using the free Adobe Acrobat Reader.

Get Adobe Reader

A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z

ANCHOR - Any device used to secure a building component to adjoining construction or a supporting member. [NOMMA-86]
Top of page

ANNEAL - To heat above the critical or recrystallization temperature, then cool metal, glass or other materials, to eliminate the effects of cold working, relieve internal stresses or improve electrical, magnetic or other properties; to soften. [NOMMA-86]
Top of page

ANODIZE - To provide a hard non-corrosive oxide film on the surface of a metal, particularly aluminum, by electrolytic action in which the metal being treated serves as the anode. [NOMMA-86]
Top of page

APPROVAL DRAWING - Drawing created to communicate the finished product to the customer. It may contain installation information not needed on a Shop Drawing. For clarity it may omit details required on the Shop Drawing.
Top of page

BALUSTER - One of a series of closely spaced upright members that support the handrail in a railing. Also referred to as a Picket, Baluster Bar, Paling, Spindle, Spacer Bar, etc. [NOMMA-86]
Top of page

BAR - A round, square, rectangular, hexagonal or similar section of rolled, drawn, or extruded metal. [NOMMA-86]
Top of page

BASKET - A double-twisted section of two, four, or eight bars, forming a rounded open basket shape. One or more baskets are then welded to bar sections to create a single basket baluster.
Top of page

BILL OF LADING - (Shipping) A written account of goods shipped by any person, signed by the agent of the owner of the carrier, acknowledging the receipt of the goods, and promising to deliver them safe at the place directed. [Webster's] Usually there are copies of the bill for the carrier, the shipper, and the consignee of the goods.
Top of page

BOTTOM RAIL - Lower member of railing system, supporting balusters or panels, if any. [NOMMA86]
Top of page

BUFFING - The process of providing a lustrous finish by means of power-operated soft fabric wheels coated with a wax compound containing fine abrasive particles. [NOMMA-86]
Top of page

BUILDING CODES - Building codes vary by locality. Responsibility for local code compliance rests with buyer, building owner, builder, architect, and/or engineer.
Top of page

BURNISHING - Developing smooth, lustrous surface of metal part by tumbling in drum containing small steel balls or by rubbing with hard pads. [NOMMA-86]
Top of page

CAP RAIL - See Handrail. [NOMMA-86]
Top of page

CASTING - A product formed by pouring molten metal into a mold. [NOMMA-86]
Top of page

CAST IRON - A hard, brittle, non-malleable metal that can be produced in any shape. It cannot be hammered or bent. It is used for many miscellaneous metal products. Both functional and decorative. [NOMMA-86 modified]
Top of page

CHAMFER - To bevel a sharp edge. [NOMMA-86]
Top of page

CHECKERED PLATE - Steel plate having a raised pattern to provide a non-slip wearing surface; referred to as "tread plate" when made of aluminum. Also called "Floor Plate" [NOMMA-86 modified]
Top of page

CIRCULAR STAIR - A stair that, in plan view, has a circular form and does not have a center column. Many building codes specify the required dimensions of a circular stair. See also Spiral Stair, Curving Stair, and Winding Stair.
Top of page

COLD-FINISHED STEEL - Carbon steel that has been cleaned and pickled, then rolled or drawn through dies to produce a dimensionally accurate section with improved surface finish and often other improved properties. [NOMMA-86]
Top of page

COLD ROLLING - Bringing metal sheet, plate or bar to final thickness and finishing by passing between heavy rollers without heating. [NOMMA-86]
Top of page

COLLAR - (1) Metal piece into which a baluster is inserted or one that encircles the baluster. Often used as an ornamental highlight in the middle portion of a plain baluster. Also refers to a band of metal that wraps around a baluster or two scrolls, etc. (2) "Collar" is also used by some as a synonym for Escutcheon. [NOMMA-86]
Top of page

COMMON CARRIER - One who undertakes the office of carrying (goods or persons) for hire. Such a carrier is bound to carry in all cases when he has accommodation, and when his fixed price is tendered, and he is liable for all losses and injuries to the goods, except those which happen in consequence of the act of God, or of the enemies of the country, or of the owner of the property himself. [Webster's]
Top of page

COPE - To cut away a portion of one member, either to form a close-fitting joint with, or provide clearance for, another member. [NOMMA-86]
Top of page

CORROSION - The decay of metals, usually from oxidation. [NOMMA-86]
Top of page

COUNTERSINKING - Beveling end of hole for receiving conical head of flat- or oval-head fastener. [NOMMA-86]
Top of page

COVER FLANGE - See Escutcheon. [NOMMA-86]
Top of page

CURVING STAIR - a generic term for a stair that, in plan view, has a circular form and does not have a center column. Circular Stairs and Winding Stairs are examples of Curving Stairs for which dimensions have been defined by building codes.
Top of page

DAYLIGHT DIMENSION - The amount of space between any two elements in a rail or stair design.
Top of page

DELIVERY DATE - The delivery date is the date when the shipment arrives at the destination. This date depends on the carrier type and the shipment destination as related to the shipment origin.
Top of page

DREAM IT. BUILD IT.™ - Custom Iron's Dream it. Build it.™ virtual design service in 3D-Viz.
Top of page

EASEMENT (Stairs) - That curved portion of a handrail that forms a transition in a vertical plane, between a horizontal and an inclined section of the handrail. [NOMMA-86]
Top of page

ELASTIC LIMIT - The maximum unit stress that can be applied to a material without causing permanent deformation. [NOMMA-86]
Top of page

EMBOSSED - Having a raised and/or indented pattern impressed on one or more surfaces by means of patterned rolls, stamping dies, or hand-forging. [NOMMA-86 modified]
Top of page

ESCUTCHEON - Protective or ornamental cover located usually at and around base of post or picket, baluster, or where a rail terminates against a wall. Also referred to as Cover Flange, Collar, Base, Shoe, Wall Clip or Wall Flange. [NOMMA-86]
Top of page

EXTRUSION - (1) The process of producing metal shapes by forcing heated metal through an orifice in a die by means of a pressure ram. (2) Any item made by this process. [NOMMA-86]
Top of page

FABRICATE - To manufacture, form, assemble or construct metal products. [NOMMA-86]
Top of page

FATIGUE - Structural failure of a material caused by repeated or fluctuating application of stress, none of which individually is sufficient to cause failure. [NOMMA-861
Top of page

FERROUS METAL - Metal in which iron is the principal element. [NOMMA-86]
Top of page

FIELD CHECK - Verification of existing dimensions against those shown on drawing prior to fabrication. [NOMMA-86]
Top of page

FIELD JOINT - A connection between two adjoining members or parts, made at the time of installation, generally accomplished by use of an internal mechanical connector or by welding. [NAAMM77]
Top of page

FIELD MEASURE - Survey of existing conditions. [NOMMA-86]
Top of page

FINIAL - An ornamental piece on top of railing post, newel or fence. Also referred to as Urn. [NOMMA-86]
Top of page

FIXED METAL STAIR - A permanently stationary series of three or more steps in one or more flights, providing pedestrian access between different floors or levels. [NAAMM-82]
Top of page

FLIGHT - An uninterrupted series of steps. [NOMMA-86]
Top of page

FLIGHT RISE - The vertical distance between the floors or platforms connected by a flight of stairs. [NOMMA-86]
Top of page

FLIGHT RUN - The horizontal distance between the faces of the first and last risers in a flight. [NOMMA-86]
Top of page

FLOOR PLATE - See Checkered Plate.
Top of page

FLOOR-TO-FLOOR HEIGHT - Dimension from the floor surface on the lower level to the floor surface of the upper level. Do not include carpet. Also known as "Finished Floor-to-Floor height". This dimension is critical when ordering a stair.
Top of page

FOB FACTORY - FOB is a shipping term meaning "Free On Board". Freight is without charge to the purchaser for delivery on board or into a carrier at a specified point or location. [American] "FOB factory" indicates that prices and liability do not include delivery from the factory dock. At Custom Iron, our product prices are quoted as FOB Factory in Zumbrota, Minnesota. We calculate shipping to your destination and add a shipping fee to the total cost of your order.
Top of page

FORGING - Heating and hammering metal into a desired shape. [NOMMA-86]
Top of page

FORMING - The process of shaping metal by mechanical action other than machining, forging, or casting. [NOMMA-86]
Top of page

GALVANIZING - The process of coating metal with zinc, either by dipping in a bath of molten zinc, by mechanical coating or electrolytic action. [NOMMA-86]
Top of page

GAUGE - (1) A number indicating the thickness of metal or the diameter of a wire or a fastener shank, in accordance with a standard series of numbers, each of which represents a certain decimal fraction of an inch (or number of millimeters). (2) The distance, in inches, between adjacent lines of holes or fasteners. [NOMMA-86]
Top of page

GENUINE WROUGHT IRON - Low carbon content used for finer types of decorative iron works where resistance to corrosion is of value. Suppliers are somewhat limited. When Genuine Wrought Iron is specified, the words "wrought iron" are not sufficient, and this term may denote any carbon steel. Therefore, in specifying, it is important that the words "Genuine Wrought Iron" be used. Also see Wrought Iron." [NOMMA-86]
Top of page

GRINDING - Removing metal from a surface by means of abrasive action. [NOMMA-86]
Top of page

HAMMERING - Hot or cold, machine or hand peening or denting of metal surfaces for artistic effect. Also referred to as Swedish Look. [NOMMA-86]
Top of page

HANDRAIL - Horizontal or sloping member normally grasped by hand. This member may be part of a railing system and often, but not necessarily, top member (top rail); or may be mounted on wall or other building element. When part of stair-rail system, it is a member paralleling the pitch of the flight and is often, but not necessarily, top member. See Wall Handrail. [NOMMA-86]
Top of page

HANDRAIL BRACKET - (1) A device attached to a wall, post or other surface to support a handrail. [NOMMA-86] (2) A device attached to a wall, post or other surface to support a handrail. A left-hand handrail bracket is one that is located on the users left as he ascends the stairs. A right-hand handrail bracket is one that is located on the user's right as he ascends the stairs. [NAAMM-77]
Top of page

HEADER, PLATFORM - A horizontal structural member supporting stair platform construction but carrying no stringers. [NOMMA-86]
Top of page

HEADROOM - The minimum vertical distance from the top surface of a stair tread or platform to the ceiling, soffit or other overhead obstruction, measured at the outer edge of a tread. [NOMMA86]
Top of page

HOT DIP GALVANIZING - The process or result of applying a protective coating to ferrous metal by dipping in a bath of molten zinc. [NOMMA-86]
Top of page

HOT ROLLED - Shaped by passing a heated billet between rollers. [NOMMA-86]
Top of page

HOT WORKING - The process of forming a metal when its temperature is higher than its recrystallization temperature. [NOMMA-86]
Top of page

INCLINE (of stairs) - See Pitch.
Top of page

I.P.S. - Iron pipe size; the nominal inside-diameter dimension of pipe. [NOMMA-86]
Top of page

KNOCKED DOWN - (1) A term used in reference to any product that is shipped disassembled, for assembly at the building site; commonly abbreviated "KD". [NOMMA-86] (2) Custom Iron ships most of its spiral stair orders KD. Assembly and installation is required at the destination. The KD shipping cost is significantly lower than shipping Set-up and the likelihood of transit damage is less.
Top of page

LAMB'S TONGUE - An ornamental curved and tapered fitting terminating a handrail. [NOMMA-86]
Top of page

LANDING - Level part of staircase at end of stair flight. See Platform. [NOMMA-86]
Top of page

LATERAL SCROLL - A fitting that curves in a horizontal plane, used to terminate a stair handrail. Often ends up as a round plate covering the top of a post. [NOMMA-86] Also called a (horizontal) volute, particularly when made of wood.
Top of page

LEAD TIME - The span of time it takes to complete an order from the order date to the shipping date. At Custom Iron, we quote lead times based on what you are planning to order. The Lead time clock starts ticking when all of the required paperwork and/or payments have been received.
Top of page

MALLEABLE IRON - A sand cast iron that is annealed and can be bent cold to some degree. It is used in many metal building products where strength and ability to resist shock are essential. It is easily welded without danger of cracking by the same method used for welding steel. [NOMMA-86]
Top of page

MECHANICAL CONNECTIONS - A connection between railing members made by means other than welding or adhesive bonding. [NAAMM-77]
Top of page

MID RAIL - Rail located between top and bottom rails. [NOMMA-86]
Top of page

MILL FINISH - The original surface finish produced on a metal mill product by rolling, extruding, or drawing. [NOMMA-86]
Top of page

MILL SCALE - The scaly oxidized surface produced on steel by heating and hot rolling. [NOMMA-86]
Top of page

MOLD - A form into which molten metal is poured to produce a casting. [NOMMA-86]
Top of page

NAAMM - National Association of Architectural Metal Manufacturers.
Top of page

NEWEL - (1) A post member supporting the end of a stair railing or serving as a common support for two stair railings. [NOMMA-86 modified] (2) The major support posts for the balustrade system. Larger and heavier than the balusters, newels are often located at the bottom and top of a staircase and at turns and critical support areas of balcony rails. Also referred to as Main Balusters.
Top of page

NON-FERROUS - Metal without any iron content. [NOMMA-86]
Top of page

NOMMA - The National Ornamental & Miscellaneous Metals Association. See references for this glossary and the Custom Iron Website Links page.
Top of page

NOSING - That part of a stair tread or platform which projects as a square, rounded or rounded and molded edge beyond the vertical face of the riser below it. [NOMMA-86]
Top of page

ORDER DATE - The date at which all specifications, drawings, acknowledgments, and required payments have been received at Custom Iron.
Top of page

PAN TREAD (Stairs) - See Tread, Pan Type. [NOMMA-86]
Top of page

PANEL - (1) Custom Iron panels are balusters or sets of balusters that are welded together to create a section of balustrade. Panels can consist of scrolls, baskets, or other ornamental elements. Often used to add unique architectural interest to the railing system, panels also reduce installation time. See also Top Bar Panel. (2) Portion of railing between posts, top rail and bottom rail. [NOMMA-86]
Top of page

PARALLEL STAIR - A stair consisting of flights which parallel each other and are separated only by one or more intermediate platforms. [NOMMA-86]
Top of page

PICKET - One of a series of closely spaced upright members that support the handrail in a railing. See baluster. [NOMMA-86]
Top of page

PICKET CASTING - Ornamental design attached to a picket. [NOMMA-86]
Top of page

PICKET RAILING - Railing consisting of posts, pickets, top rail and, sometimes, bottom rail. [NOMMA-86]
Top of page

PIN TOP BALUSTER - Custom Iron's optional pin top balusters add a round peg-like extension at the ends of square bar balusters. The pin top simplifies installation into the wood stairs and handrail of the stair system.
Top of page

PIPE RAILING - Railing fabricated of pipe. [NOMMA-86]
Top of page

PIPE, ROUND - A hollow round section of metal, the size of which is usually designated by nominal inside diameter in inches (or millimeters). [NOMMA-86]
Top of page

PITCH - The inclination or slope, measured either in degrees, percent, or by the ratio of rise to run. [NOMMA-86]
Top of page

PITCH DIMENSION (Stairs) - The distance between the bases of the top and bottom risers in a flight, measured parallel to the slope. Sometimes referred to as the nose-to-nose dimension. [NOMMA-86]
Top of page

PLATFORM (Stairs) - A horizontal surface usually having a dimension parallel to the stringer greater than a tread width and occurring in a stair at the end of a flight or between flights, either at a floor level or between floors. In the latter case, it is sometimes referred to as an intermediate platform or landing. [NOMMA-86 modified]
Top of page

PLATFORM HEADER - See Header, Platform. [NOMMA-86]
Top of page

POCKET - Opening provided in structure to accept post, rail-supporting bracket or structural member. [NOMMA-86]
Top of page

POST (Railing) - A vertical, supporting member of a railing system. [NOMMA-86]
Top of page

PRE-ASSEMBLED STAIR - A stair whose components are assembled in the plant to make up units of varying sizes and degrees of complexity. [NAAMM-82]
Top of page

PRIMER PAINT - First coat applied to metal to retard corrosion temporarily and to provide satisfactory adhesion of finish coat. [NOMMA-86]
Top of page

PUNCHING - A process of forcing a punch through the metal into a die, forming a hole in the shape of the punch. [NOMMA-86]
Top of page

RAILING SYSTEM - An assembly of any of a wide selection of materials that serves as a vertical safety barrier located at the edge of a stair, platform or floor. It often supports a handrail. See Stair Rail System. [NOMMA-86 modified]
Top of page

RAKE - See Pitch. [NOMMA-86]
Top of page

RAKE DIMENSION - See Pitch Dimension. [NOMMA-86]
Top of page

RAMP RAIL, SYSTEM - A railing system located along side(s) of ramp. [NOMMA-86]
Top of page

RESTOCKING FEE - A fee charged by the seller for items that will be returned to stock. A restocking fee usually covers the seller's cost for paperwork and handling of a returned item.
Top of page

RETURN - A rail bend of 180°, as at a stair platform or railing terminal. See also Wall Return. [NAAMM-77]
Top of page

RETURNED MATERIAL AUTHORIZATION (RMA) - An authorization from a manufacturer required prior to returning all or portions of an order. The RMA number given at the time the RMA is requested must appear on all returned packages.
Top of page

RISE - See Flight Rise. [NOMMA-86]
Top of page

RISER - The vertical or inclined face of a step, extending from the back edge of one tread to the outer edge of the tread or lower edge of the nosing next above it. [NOMMA-86]
Top of page

RISER, OPEN - A term used to describe a stair having open spaces rather than risers between treads. [NOMMA-86]
Top of page

RISER HEIGHT -The vertical distance between the top surfaces of two successive treads. [NOMMA86]
Top of page

RUN - See Flight Run and Tread Run. [NOMMA-86]
Top of page

SAND BLASTING - Subjecting to a stream of sand projected at high velocity under air or steam pressure, for the purpose of removing scale or encrusted material or to provide a textured finish. [NOMMA-86]
Top of page

SCROLL - Ornamental spiral or convoluted form serving, e.g., as decorative railing panel or insert, either cast or forged. [NOMMA-86]
Top of page

SET-UP - In shipping, when a product is shipped fully assembled. Usually significantly higher shipping costs than a Knocked Down shipment.
Top of page

SHIP DATE - The date when an order leaves the shipping origin for transport to the shipping destination. The delivery date is the date when the shipment arrives at the destination.
Top of page

SHOP DRAWING - A drawing created to communicate the finished product to the fabricator. An Approval Drawing may at times be used as a Shop Drawing.
Top of page

SLAG - The crusty residue resulting from melting or welding metal. [NOMMA-86]
Top of page

SLEEVE - (1) A tubular section of sheet metal or other material placed in concrete or masonry to provide either a pocket or opening for the insertion or the penetration of another item. (2) An internal tubular splice between abutting sections of pipe, tubing, or tube-like members. [NOMMA-86]
Top of page

SLOPE - See pitch. [NOMMA-86]
Top of page

SPECIFICATIONS - Document providing descriptive or performance requirements and criteria. [NOMMA-86]
Top of page

SPINDLE - A tapered round picket, with center part larger in diameter than ends. [NOMMA-86]
Top of page

SPIRAL STAIR - A stair with a closed circular form, uniform sector-shaped treads and a supporting center column. [NOMMA-86]
Top of page

STAIR-RAIL SYSTEM - Railing system located along open sides of stair and landing. [NOMMA-86]
Top of page

STAIR-RUN - One run of stairs between floors, platforms or floors and platforms. [NOMMA-86]
Top of page

STAIRWELL - The vertical shaft space in a building occupied by a stair; also, the open well space between a series of flights. [NOMMA-86]
Top of page

STEP - The combination of a riser and the tread immediately above it. [NOMMA-86]
Top of page

STEP RISE - See Riser Height. [NAAMM-82]
Top of page

STORY HEIGHT - The vertical distance, in a building, between one finished floor and the next.
Top of page

STRAIGHT RUN STAIR - Stair extending in straight line between two floors and consisting of single flight or series of flights with one or more intermediate platforms. [NOMMA-86]
Top of page

SUB-TREAD - See Tread, Pan Type. [NOMMA-86]
Top of page

TEMPERING - The process of heating metal, glass or other material to temperature below transformation stage, subsequently cooling it at controlled rate to change its hardness, strength, toughness or other property. [NOMMA-86]
Top of page

TEMPLATE -A pattern used as a guide. Custom Iron sometimes supplies hole placement templates for easy installation of metal railing systems.
Top of page

TENSILE STRENGTH - The maximum load that can be sustained by metal in tension measured in pounds per square inch. [NOMMA-86]
Top of page

TOLERANCE - Permissible deviation from a nominal or specified dimension or value. [NOMMA-86]
Top of page

TOP BAR PANEL - Custom Iron's Top Bar Panel is a framework for your balusters. The balusters that you choose are welded to a low-profile top bar that then creates a rigid section or panel. The Top Bar Panel can be easily fastened to a wood or metal handrail, rail cap or rail.
Top of page

TOP RAIL - The top member of a rail system, sometimes called cap rail. [NOMMA-86]
Top of page

TREAD - The horizontal member of a step. [NOMMA-86]
Top of page

TREAD DEPTH - The tread run plus the projection of the nosing, if any. [NOMMA-86]
Top of page

TREAD, GRATING TYPE - Tread fabricated from metal grating. [NOMMA-86]
Top of page

TREAD LENGTH - The dimension of a tread measured perpendicular to the normal line of travel on a stair. [NOMMA-86]
Top of page

TREAD, PAN TYPE - A tread shaped to receive a fill and provide, when filled, either a tread or a combination tread and riser. [NOMMA-86 modified]
Top of page

TREAD, PLATE TYPE - A tread, or a combination of tread and riser, fabricated from metal plate, floor plate, tread plate or a combination of plates. [NOMMA-86]
Top of page

TREAD RUN - The horizontal distance between two consecutive risers or, on an open riser stair, the horizontal distance between nosings or the outer edges of successive treads, all measured perpendicular to the front edges of the nosings or treads. [NOMMA-86]
Top of page

TREAD WIDTH - The tread run plus the projection of the nosing, if any. [NAAMM-82]
Top of page

TUBING - A hollow section of metal having a round, square, rectangular or other cross-sectional form. Size is designated by outside dimension(s) in inches or millimeters, and wall thickness in gauge number, thousandths of an inch, or millimeters, or fraction of an inch. [NOMMA-86]
Top of page

VERTICAL BARRIER - A wall or railing adjacent or attached to the edge of a flight, platform or floor, to prevent persons from falling. [NAAMM-82]
Top of page

VOLUTE (Stairs) - A spiral or scroll-shaped fitting used to terminate a stair handrail. [NOMMA-86]
Top of page

WALL HANDRAIL - Handrail attached to wall adjacent to stair and paralleling pitch of flight, also used along walkway, ramps and corridors. Also referred to as a Wall Rail. [NOMMA-86]
Top of page

WALL RETURN - A bend at the end of a wall handrail, turning it toward the wall to which it is attached. [NOMMA-86]
Top of page

WELDING - The process of joining two metals or alloys by fusion. [NOMMA-86]
Top of page

WINDING STAIR - A stair that, in plan view, has a circular form and does not have a center column. Many building codes specify the required dimensions of a winding stair. See also Spiral Stair, Curving Stair and Circular Stair.
Top of page

WROUGHT IRON - Fabricated ornamental work, usually made of mild steel of commercial quality. Also see Genuine Wrought Iron. [NOMMA-86]
Top of page

REFERENCES

National Association of Architectural Metal Manufacturers (NAAMM). METAL STAIRS MANUAL. 1982. Fourth Edition.
Top of page

National Association of Architectural Metal Manufacturers (NAAMM). PIPE RAILING MANUAL: Including Round Tube. 1977.
Top of page

National Ornamental & Miscellaneous Metals Association (NOMMA). METAL RAIL MANUAL. A Guide for Architects, Designers, Fabricators, and Installers. 1986. Second Edition.
Top of page

Custom Iron modifications to a NOMMA definition [NOMMA 86 - modified]
Top of page

Webster's Revised Unabridged Dictionary, © 1996, 1998
Top of page

The American Heritage® Dictionary of the English Language, Fourth Edition Copyright © 2000 by Houghton Mifflin Company.

Top of page